VW T6.1 - APP-control for parking heater (water)

Control the parking heater with your mobile phone simply by APP, SMS or Call.

Suitable for the following vehicles with factory installed parking heater (Webasto Thermotop EVO).

• VW T6.1 with waterheater and remote control
• VW T6.1 with waterheater without remote control

Installation

The installation of the APP-control depends on the installed operating device and parking heater.

With remote control

The waterheater can be controlled via a radio remote control.

In the case, the APP-control is connected "plug & play" to the original receiver of the radio control, using the included y-cable.
The APP-control works like the original radio control, so you can switch both heaters (if installed).
However, you will have to select which heater can be switched via APP-control like you would do for the original radio remote.

Without remote control

The waterheater can be controled via the control panel at the roof only.

In this case, the APP-control is connected "plug&play" to the connector of the heater beneath the drivers seat using our y-cable which is included into delivery.

Please note: The entry "radio remote installed" has to be activated using VCDS.

Features

• Switching by APP, SMS or Call
• 5 authorized numbers
• 24h timerfunction
• Input for external switch
• Alarmfunction
• Input for external temp. sensor
• GPS-positioning (optional)
• external temperature sensor (optional)

Network coverage

Future-proof due to 4G (LTE) technology.

Our new APP-control v11x supports not only the 4G (LTE) standard but still 3G (UMTS) and 2G (GSM) mobile networks.
This way we can achieve the best possible reachability and functionality in all current european mobile phone networks.

Switzerland is about the shutdown the 2G (GSM) mobile network until the end of 2020. Devices which support the 2G standard only are not functional anymore.
The date for shutting down the 2G network in germany is not yet known.

GPS-Positioning

The APP-control supports an external GPS-receiver which can be connected to the aux-socket at the back of the module. If the ignition is switched on the position is determined about every 1 second and can be queried via SMS. If the ignition is switched off, the GSP-receiver is activated to determine the position only. You will get a SMS containing the coordinates of the car as well as a link to "google maps" which shows the current position on the map.

 

Alarminput

You can connect an already existing alarmsystem to the APP-control. You will be informed via SMS and call as soon as the alarm is triggered.

The alarmsystem must output a +12v signal when triggered. For further information please have a look at our "installation guide" on this webpage.

 

Safety

The parking heater can only controlled via "authorized numbers". You can configure these numbers simply by SMS. The integrated GSM-module has a temperature range from -30°C up to 80°C to ensure proper function at all conditions.

 

APP, SMS, Call

You can control the parking heater by APP, SMS, or Call. Switching the heater by call is free of charge as there is no connection established. Switching the heater by SMS can cause additional costs, depending on your mobile provider. APP’s are sending SMS in the background, so there could arise additional costs too.

The APP-control requires a SIM-card wich is not included into delivery. You can use every SIM-card which supports sms and call e.g. prepaid card.

 

Technical data

• voltage supply: 10 - 15VDC
• current consumption: standby <10mA, login: briefly 2A
• antenna connection: internal antenna
• SIM-card: nano-SIM
• temperature range: -30°C bis 80°C
• GSM-module: 4G (LTE), 3G (UMTS), 2G (GSM)
• dimensions: 63x60x22mm (LxWxH)

Scope of delivery

• danhag APP-control
• vehicle specific connection cord
• users manual
• GPS-receiver *

*  if you select "with GPS"  the GPS-receiver will be included into delivery .