VW T5 - APP-control for parking heater (water)
Prices incl. VAT plus shipping costs
Ready to ship today,
Delivery time appr. 1-3 workdays
- Order number: 6235-154
Control the parking heater with your mobile phone simply by APP, SMS or Call.
Suitable for the following vehicles with factory installed parking heater with and without radio remote control:
- VW T5 with remote control
- VW T5 without remote control
Installation
The installation of the APP-control depends on the configuration of the vehicle.
With remote control
The APP-control is connected "plug & play" to the original receiver of the radio remote control using the included Y-cable.
Without remote control
The APP-control is connected directly to the heater.
Features
- Switching by APP, SMS or Call
- 5 authorized numbers
- 24h timerfunction
- Input for external switch
- Alarmfunction
- Input for external temp. sensor
- GPS-positioning (optional)
- external temperature sensor (optional)
Network coverage
Future-proof due to 4G (LTE) technology.
Our new APP-control v11x supports not only the 4G (LTE) standard but still 3G (UMTS) and 2G (GSM) mobile networks.
This way we can achieve the best possible reachability and functionality in all current european mobile phone networks.
Switzerland is about the shutdown the 2G (GSM) mobile network until the end of 2020. Devices which support the 2G standard only are not functional anymore.
The date for shutting down the 2G network in germany is not yet known.
GPS-Positioning
The APP-control supports an external GPS-receiver which can be connected to the aux-socket at the back of the module. If the ignition is switched on the position is determined about every 1 second and can be queried via SMS. If the ignition is switched off, the GSP-receiver is activated to determine the position only. You will get a SMS containing the coordinates of the car as well as a link to "google maps" which shows the current position on the map.
Alarminput
You can connect an already existing alarmsystem to the APP-control. You will be informed via SMS and call as soon as the alarm is triggered.
The alarmsystem must output a +12v signal when triggered. For further information please have a look at our "installation guide" on this webpage.
Safety
The parking heater can only controlled via "authorized numbers". You can configure these numbers simply by SMS. The integrated GSM-module has a temperature range from -30°C up to 80°C to ensure proper function at all conditions.
APP, SMS, Call
You can control the parking heater by APP, SMS, or Call. Switching the heater by call is free of charge as there is no connection established. Switching the heater by SMS can cause additional costs, depending on your mobile provider. APP’s are sending SMS in the background, so there could arise additional costs too.
The APP-control requires a SIM-card wich is not included into delivery. You can use every SIM-card which supports sms and call e.g. prepaid card.
Technical data
- voltage supply: 10 - 15VDC
- current consumption: standby <10mA, login: briefly 2A
- antenna connection: internal antenna
- SIM-card: nano-SIM
- temperature range: -30°C bis 80°C
- GSM-module: 4G (LTE), 3G (UMTS), 2G (GSM)
- dimensions: 63x60x22mm (LxWxH)
Scope of delivery
- danhag APP-control
- vehicle specific connection cord
- users manual
- GPS-receiver *
* if you select "with GPS" the GPS-receiver will be included into delivery .
Installation
The parking heater can be controlled either via a radio remote control or via the operating device at the roof lining.
The installation of the APP-control depends on the configuration of the vehicle.
With remote control
The APP-control is connected plug&play to the original receiver using the included Y-cable.
The receiver is mounted at the drivers footwell behind the cover of the A-pillar.
Outputsignal
- W-BUS 3
Without remote control
The output-line (yellow) of the APP-control is connected directly to PIN1 of the heater.
The heater is mounted beneath the car on the left side, behind a cover.
Installation of the APP-control
- Remove the cover of the heater.
- Loosen the brackets of the heater.
- Lower the heater.
(You don't have to remove the water hoses.) - Unplug the 6-pin connector of the heater.
(The connector is located on the top of the heater.) - Connect the output-line (yellow) of the APP-control to PIN1 of the heater.
- Connect the APP-control to the power supply.
(The powersupply can be found below the drivers seat, +12V, ground.)
We recomment to use our universal connection cord with crimpcontact. This lin can be easily
Outputsignal
- W-BUS 3